铝合金表面GPTMS硅烷膜的制备及耐蚀性能研究

为提高铝合金耐腐蚀力，运用正交试验法研究在铝合金表面制备 γ-（2，3-环氧丙氧）丙基三甲氧基硅烷（GPTMS）自组装膜最佳工艺条件，利用极化曲线和扫描电子显微镜研究该硅烷膜在铝合金表面的耐腐蚀性能。研究表明：最佳工艺条件为 100 mL溶液中， pH＝4. 5，V（GPTMS）∶V（EtOH）∶V（H₂O）= 2∶7∶91，T_{1（水解温度）}＝25 ℃，t_{1（水解时间）}＝7 h，t_{2（浸涂时间）}＝10 min，t_{3（固化时间）}＝90 min，T_{2（固化温度）}＝120 ℃，该工艺条件下制备的硅烷膜具有优异的耐腐蚀性能。     

耐腐蚀水性铝颜料的制备及表征

为了提高铝颜料在水性涂料中的耐腐蚀性能，以正硅酸乙酯（ TEOS）为前驱物，通过溶胶-凝胶反应在铝颜料表面形成了一层致密的二氧化硅包覆薄膜，通过优化固含量、溶剂种类及 TEOS的用量，提高铝颜料的耐碱性。利用扫描电镜、刮板试验、接触角测试、析氢实验进行表征，结果表明：以无水乙醇为溶剂，铝金属颜料固含量为 10%，升温至 50 ℃后，逐滴加入 6 g TEOS，再升温至 80 ℃，该条件下制备的 SiO₂膜包覆后的铝颜料具有优异的耐碱性，同时表面性能由疏水性转变成亲水性，对铝颜料起到了很好的保护作用。     

规整有机分子自聚集体对铜的高效缓蚀的研究

通过多步法合成了离子型含双苯并三氮唑环的目标分子，4，4'-{苯-1，3-二基二[(1E)-3-羰基丙-1-烯-1，3-二基]}二[2-(2H-苯并三唑-2-基)苯醇酸]二钾。在室温条件下，目标分子在3.5%（质量）NaCl/DMSO（二甲基亚枫）混合溶液 （体积比：40/60） 中能够发生分子自组装产生纳-微米级的自聚集体。通过傅里叶变换红外光谱 （FT-IR）、拉曼光谱和X射线光电子能谱 （XPS） 的表征，证实了所形成的目标分子自聚集体能够对铜表面产生强烈的化学吸附作用，在铜表面形成自组装膜。利用电化学方法测定了目标分子自聚集体吸附在铜表面形成自组装膜后，在3.5%（质量）NaCl溶液中的缓蚀性能。结果表明目标分子自聚集体在NaCl溶液中能高效地抑制铜腐蚀。     

Corrosion behavior of air plasma spraying zirconia-based thermal barrier coatings subject to Calcium–Magnesium–Aluminum-Silicate (CMAS) via burner rig test

Three different kinds of thermal barrier coatings (TBCs) — 8YSZ, 38YSZ and a dual-layered (DL) TBCs with pure Y₂O₃ on the top of 8YSZ were produced on nickel-based superalloy substrate by air plasma spraying (APS). The Calcium–Magnesium–Aluminum-Silicate (CMAS) corrosion resistance of these three kinds of coatings were researched via burner rig test at 1350 °C for different durations. The microstructures and phase compositions of the coatings were characterized by SEM, EDS and XRD. With the increase of Y content, TBCs exhibit better performance against CMAS corrosion. The corrosion resistance against CMAS of different TBCs in descending was 8YSZ + Y₂O₃, 38YSZ and 8YSZ, respectively. YSZ diffused from TBCs into the CMAS, and formed Y-lean ZrO₂ in TBCs because of the higher diffusion rate and solubility of Y³⁺ in CMAS than Zr⁴⁺. At the same time, 38YSZ/8YSZ + Y₂O₃ reacts with CAMS to form Ca₄Y₆(SiO₄)₆O/Y_4·67(SiO₄)₃O with dense structure, which can prevent further infiltration of CMAS. The failure of 8YSZ coatings occurred at the interface between the ceramic coating and the thermally grown oxide scale (TGO)/bond coating. During the burner rig test, the Y₂O₃ layer of the DL TBCs peeled off progressively and the 8YSZ layer exposed gradually. DL coatings keep roughly intact and did not meet the failure criteria after 3 h test. 38YSZ coating was partially ablated, the overall thickness of the coating is thinned simultaneously after 2 h. Therefore, 8YSZ + Y₂O₃ dual-layered coating is expected to be a CMAS corrosion-resistant TBC with practical properties.     

用于低损耗特种玻璃熔炼的高纯致密锆英石的研制

以纯度大于99.9%(质量分数)的高纯ZrO₂和SiO₂为原料,少量TiO₂为添加剂,采用高温固相法合成高纯锆英石(ZrSiO₄)粉料。研究温度和反应时间对高纯锆英石合成效率的影响,发现粒度小于50 μm的原料粉末经1 500 ℃反应48 h后,ZrSiO₄相的含量可以达到95.77%(质量分数)。将合成的高纯锆英石粉料球磨并冷等静压成型后,在1 550 ℃高温烧结成高纯致密锆英石砖。高纯致密锆英石中杂质Fe的含量仅为29 μg/g,Cu的含量小于1 μg/g,是普通商用致密锆英石的1/10;对磷酸盐玻璃静态光吸收损耗的影响仅为普通致密锆英石材料的1/3。将这种高纯致密锆英石材料用于激光玻璃窑炉,有助于降低玻璃对1 053 nm激光的损耗,提升激光玻璃的激光性能。     

TRT叶片腐蚀与磨损的研究

研究了TRT叶片腐蚀磨损的原理,选择合适的材料,采用合理的喷涂方式,通过实验表明,试样1(Co-87WC)涂层是抗冲蚀磨损的最佳选择,而试样4涂层(Ti N)则不适合TRT叶片的使用环境。     

Effect of aluminum on microstructure,mechanical properties and pitting corrosion resistance of ultra-pure 429 ferritic stainless steels

Effect of aluminum on microstructure, mechanical properties and pitting corrosion resistance of ultra-pure 429 ferritic stainless steels has been investigated. Aluminum can significantly increase the ratio of equiaxed crystal grains, but the promotion effect has great relation with aluminum content. Aluminum can stabilize ferrite phase and significantly reduce recrystallization temperature. Increased aluminum content can also lead to the precipitate of AlN and Al₂O₃ at higher temperature. The increased amount of AlN may partly contribute to the reduced nitrogen element to form austenite at high temperature, hence the high temperature phase transformation of α + γ → α occurs. The fine and large number of Al₂O₃ particles can refine grain size and then promote recrystallization. The highest intensity of γ-fiber texture {1 1 1}〈1 1 2〉 is observed in the steel with 0.19 wt.% aluminum, which can improve the formability of steels. With the increase of aluminum content, the tensile strength increases linearly but the elongation and plastic strain ratio first increase then decrease, the working hardening index varies slightly among the steels. Appearance of Al₂O₃ inclusions with small size and decreased content of MnS benefit pitting corrosion resistance. However, the large dimension Al₂O₃ inclusions have significantly negative influence on pitting corrosion resistance.